基于分形理论的黄河内蒙古段河势演变特征及其与凌汛灾害关联研究

寒区河道凌汛灾害河势“弯道效应”的量化评估十分重要。基于分形理论提出河道横断面-纵剖面-平面多维度河势分形维数计算方法及其物理机制，并探讨黄河内蒙古段不同维度河势演变分形特征及其与凌汛灾害的关联关系。结果表明，黄河内蒙古段不同维度河势均具有多尺度自相似分形特征，且具有多年记忆周期的长程相关性；冰坝（严重性冰塞）发生频次与河道主槽弯曲分形维数呈正相关指数型函数关系，与河相系数、深泓点高程和河段平均底坡分形维数负相关，与水深-面积分形维数正相关，总体表明冰坝灾害更易发生于主槽偏移摆动大、蜿蜒曲折、河湾发育程度高的宽浅型弯曲河道，研究成果可为凌汛期冰塞冰坝灾害易发河段诊断及预测提供重要理论依据。     

基于VMD和BSA-KELM的高陡边坡位移预测模型研究

边坡位移的时间序列曲线存在复杂的非线性特性,传统的预测模型精度不足以满足预测要求。为此提出了基于变分模态分解的鸟群优化-核极限学习机的预测模型,并用于河北省某水泥厂的边坡位移预测。该方法首先采用VMD把边坡位移序列分解为一系列的有限带宽的子序列,再对各子序列分别采用相空间重构并用核极限学习机预测,采用鸟群算法优化相空间重构的嵌入维度和KELM中惩罚系数和核参数三个数值,以取得最优预测模型。最后将各个子序列预测值叠加,得到边坡位移的最终预测值。结果表明：和KELM、BSA-KELM、EEMD-BSA-KELM模型相比,基于VMD的BSA-KELM预测精度更高,为边坡位移的预测提供一种有效的方法。     

Cu-template-dependent synthesis of PtCu nanotubes for oxygen reduction reactions

The development of electrocatalysts with high activity and durability for oxygen reduction reaction (ORR) in acidic electrolyte environments remains a serious challenge for clean and efficient energy conversion. Synergistic effects between Pt and inexpensive metals, the d band center of Pt and catalyst morphology could adjust the adsorption and desorption of oxygen intermediates by the Pt. All the factors affect the catalytic performance of Pt-based nanocrystals. Here, we prepared Cu@PtCu₃ NWs with an average diameter of 74.9 nm for Cu and about 10 nm PtCu₃ layer. After etching, the Cu@PtCu₃ nanowires is transformed into PtCu nanotube structure, due to the removal of copper from the surface and interior. PtCu NTs for ORR shows excellent activities and durability due to the integration of structural advantages and synergistic effects. Notably, the mass activity and specific activity of PtCu NTs (0.105 A mg^?1_Pt and 0.230 mA cm^?2_Pt) are 2.0 and 3.8 times higher than that of commercial Pt/C (0.053 A mg^?1_Pt and 0.06 mA cm^?2_Pt). The etching process to change the morphology of the catalyst and alter the electronic structure of the catalyst is expected to be useful for the design of future structured Pt-based alloy nanocatalysts.     

An Optimized Combination of Mine Water Control,Treatment, Utilization,and Reinjection for Environmentally Sustainable Mining: A Case Study

This paper presents a case study of an optimized combination of mine water control, treatment, utilization and reinjection to achieve the zero discharge of mine water. Mine water has been considered a hazard and pollution source during underground mining, so most mining enterprises directly discharge mine water to the surface after simple treatment, resulting in a serious waste of water. Moreover, discharging a large amount of mine water can destroy the original groundwater balance and cause serious environmental problems, such as surface subsidence, water resource reduction and contamination, and adverse impacts on biodiversity. The Zhongguan iron mine is in the major groundwater source area of the Hundred Springs of Xingtai, which is an area with a high risk of potential subsidence. To optimize the balance between mining and groundwater resources, a series of engineering measures was adopted by the Zhongguan iron mine to realize mine water control, treatment, utilization, and reinjection. The installation of a closed grout curtain has greatly reduced the water yield of deep stopes in the mine; the effective sealing efficiency reaches 80%. Nanofiltration membrane separation was adopted to treat the highly mineralized mine water; the quality of the produced water meets China’s recommended class II groundwater standard. Low-grade heat energy from the mine water is collected and utilized through a water-source heat pump system. Finally, zero mine water discharge is realized through mine water reinjection. This research provides a beneficial reference for mines with similar geological and hydrogeological conditions to achieve environmentally sustainable mining.

     

A novel method of shrimp blanching by CO2 heat pump: Quality,energy, and economy analysis

To reduce the energy consumption of the shrimp blanching process and improve the economic value of the blanched product, a transcritical CO₂ heat pump blanching system (THPB system) was designed in this paper. The trends of astaxanthin were investigated at atmospheric pressure near boiling temperature, combined with the color and structural properties of shrimp samples, and the optimal blanching times of 270 s and 240 s were obtained at 90°C and 95°C, respectively. In contrast to the fuel blanching system (FB system) at 100°C, the annual standard coal consumption of the THPB system with 90°C blanching is decreased by 79%, and the annual operating cost can be saved by CNY 63,800, with a payback period of about 3.13 years.Industrial relevanceBlanching is one of the effective ways to prolong the shelf life of shrimp. However, the research on the blanching time and temperature of shrimp is not comprehensive. In addition, the traditional fuel blanching process has high energy consumption and pollution, and can no longer meet the quality requirements of the modern food processing industry. Heat pump has been shown to have better performance in food drying, but it is less used in blanching. The information presented in this study may provide other insights into food processing.     

Mechanical Properties of Single-Layer Diamond Reinforced Poly(vinyl alcohol) Nanocomposites through Atomistic Simulation

Low-dimensional carbon nanostructures are ideal nanofillers to reinforce the mechanical performance of polymer nanocomposites due to their excellent mechanical properties. Through molecular dynamics simulations, the mechanical performance of poly(vinyl alchohol) (PVA) nanocomposites reinforced with a single-layer diamond – diamane is investigated. It is found the PVA/diamane exhibits similar interfacial strengths and pull-out characteristics with the PVA/bilayer-graphene counterpart. Specifically, when the nanofiller is fully embedded in the nanocomposite, it is unable to deform simultaneously with the PVA matrix due to the weak interfacial load transfer efficiency, thus the enhancement effect is not significant. In comparison, diamane can effectively promote the tensile properties of the nanocomposite when it has a laminated structure as it deforms simultaneously with the matrix. With this configuration, the interlayer sp³ bonds endows diamane with a much higher resistance under compression and shear tests, thus the nanocomposite can reach very high compressive and shear stress. Overall, enhancement on the mechanical interlocking at the interface as triggered by surface functionalization is only effective for the fully embedded nanofiller. This work provides a fundamental understanding of the mechanical properties of PVA nanocomposites reinforced by diamane, which can shed lights on the design and preparation of next generation high-performance nanocomposites.     

基于蜻蜓翅脉结构的连续碳纤维增强树脂基复合材料仿生设计与增材制造

以具有轻质高强优异性能的蜻蜓翅脉结构为设计灵感，在分析翅脉网格结构抗冲击原理的基础上，设计了传统和仿生两类对比结构。采用熔融挤出3D打印机成功制备了具有不同结构的连续碳纤维增强聚乳酸复合材料试样，并对不同结构复合材料试样的拉伸性能和抗冲击性能进行了测试和对比分析。研究分析结果表明：由于拉伸力方向上的连续碳纤维含量相对较少，限制了仿生结构复合材料抗拉强度的提高，但仿生结构的平均抗拉强度为传统结构的1.18倍；当仿生结构复合材料试样受到冲击力时，其内部六边形结构的连接角度会发生变化，从而极大消耗冲击能量，同时具有六边形网格结构的连续碳纤维可以有效阻碍裂纹的扩展，因此仿生结构的平均冲击韧性可以达到传统结构的2.46倍；仿生蜻蜓翅脉结构可以显著提高增材制造复合材料的综合力学性能，且对于抗冲击性能的提高具体突出效果。连续碳纤维增强树脂基复合材料的有效可行的仿生蜻蜓翅脉结构设计和增材制造，可极大扩展其在高冲击载荷领域中的相应应用。     

Evaluation of Scale and Corrosion Inhibition of Modified Polyaspartic Acid

Amino acid modified polyaspartic acids were evaluated as calcium-scale inhibitors. Feasibility of scale inhibition experiments was analyzed by molecular dynamics simulation and Gaussian optimization, and the scale inhibition mechanism was theoretically analyzed. Scale inhibition performance was studied by scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, static scale inhibition experiments, and electrochemical performance testing, which provided an experimental basis for the molecular dynamics simulation. The experimental results showed that Arg-SA-PASP has better scale inhibition and corrosion inhibition performance than His-SA-PASP. The scale inhibition effect increased with increasing concentration. Electrochemical tests indicated that Arg-SA-PASP is an excellent scale and corrosion inhibitor.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Looking ahead: Joint small group detection and tracking in crowd scenes

Small group detection and tracking in crowd scenes are basis for high level crowd analysis tasks. However, it suffers from the ambiguities in generating proper groups and in handling dynamic changes of group configurations. In this paper, we propose a novel delay decision-making based method for addressing the above problems, motivated by the idea that these ambiguities can be solved using rich temporal context. Specifically, given individual detections, small group hypotheses are generated. Then candidate group hypotheses across consecutive frames and their potential associations are built in a tree. By seeking for the best non-conflicting subset from the hypothesis tree, small groups are determined and simultaneously their trajectories are got. So this framework is called joint detection and tracking. This joint framework reduces the ambiguities in small group decision and tracking by looking ahead for several frames. However, it results in the unmanageable solution space because the number of track hypotheses grows exponentially over time. To solve this problem, effective pruning strategies are developed, which can keep the solution space manageable and also improve the credibility of small groups. Experiments on public datasets demonstrate the effectiveness of our method. The method achieves the state-of-the-art performance even in noisy crowd scenes.